SK Series Pure Sine Wave Inverter User’s Manual
245.00 [9.65]56.00 [2.20]SK2000 368.00 [14.49]SK3000 398.00 [15.67]Pure Sine Wave Power Inverter166.00 [6.53]209.00 [8.23]AC OUTPUTPURE SINE WAVE INVE
3. Introduction This power inverter series is one of the most advanced line of mobile AC power systems. To get the most effective power inverter, it m
3-1-3. Input Level:Display Input Voltages LED Status DC 12V DC 24V DC 48V RED Slow Blink 10.3~10.6 20.5~21.2 40.8~42.4 RED 10.6~11.0 21.2~21.8
3-1-6. Status:Display Power & Fault Status Green LED LED Signal StatusSolid Power OK Slow Blink Power SavingRed LED LED Signal Status PVO kn
3-1-8. AC outlets (available): Australia / New ZealandIEC-2UniversalHARD WIREUnited KingldomIEC-1North America (GFCI)NEMA 5-15RNEMA 5-20RContinental E
3-2. Rear Panel Operations:SK700SK1000SK15003-2-1. Remote Port:The SK Series Inverter is compatible with any of the remote controllers, CR-6, CR-7 or
3-2-3. DC Input Terminal:Connect DC input terminal to 12V / 24V / 48V battery or the other power sources. 【+】represents positive, and【-】represents neg
3-4. Installation:The power inverter should be installed in an environment that meets the following requirements:3-4-1. Dry – Do not allow water to dr
3-5. DC Wiring Connections:Follow this procedure to connect the battery cables to the DC input terminalsof the Inverter. The cables should be as sh
3-5-1. Connect the cables to the power input terminals on the rear panel of the inverter. The red terminal is represents positive (+) and black ter
1. Important Safety Instructions 1-1. General Safety Precautions 1-1-1. Do not expose the Inverter to rain, snow, spray, bilge or dust. To reduce risk
PORTCHASSISGROUNDREMOTE NEG(-)POS(+)DC INPUTINLINE FUSESK1000SK700SK1500SK2000SK3000INLINE FUSEREVERSE POLARITY WILL DAMAGE UNITSHOCK HAZARD.DO NOT
3-6. AC Safety Grounding:The AC output ground wire should go to the grounding point for your loads ( for example, a distribution panel ground bus ). 3
3-7. Inverter Operation:To operate the power inverter, use the ON / OFF switch on the Front panel to turn the power on. Then the power inverter is
4. Troubleshooting:Problems and Symptoms Possible Cause Solutions “No AC Power Output” STATUS illuminates the red LED a. Blinking fast Over input v
5. Maintenance:To keep your inverter operating properly, there is very little maintenance required. You should clean the exterior periodically with a
2. Features Pure sine wave output (THD < 3%)Output frequency:50 / 60Hz switch selections Input & output fully isolated design Power Saving Mo
2-2. Electrical PerformanceSpecificationModel No. ItemSK700-112 SK700-124 SK700-148 SK700-212 SK700-224 SK700-248 W007 rewoP tuptuO suounitnoC W077
SpecificationModel No. ItemSK1000-112 SK1000-124 SK1000-148 SK1000-212 SK1000-224 SK1000-248 W0001 rewoP tuptuO suounitnoC W0011 rewoP tuptuO mumixa
SpecificationModel No. ItemSK1500-112 SK1500-124 SK1500-148 SK1500-212 SK1500-224 SK1500-248 W0051 rewoP tuptuO suounitnoC W0561 rewoP tuptuO mumixa
SpecificationModel No. ItemSK2000-112 SK2000-124 SK2000-148 SK2000-212 SK2000-224 SK2000-248 W0002 rewoP tuptuO suounitnoC W0022 rewoP tuptuO mumixa
SpecificationModel No. ItemSK3000-112 SK3000-124 SK3000-148 SK3000-212 SK3000-224 SK3000-248 W0003 rewoP tuptuO suounitnoC W0033 rewoP tuptuO mumixa
2-3. Mechanical Drawings REMOTE PORTCHASSISGROUNDSK700 273.00 [10.75] SK1000 340.00 [13.39]SK1500 370.00 [14.57]SK700 33.5 [1.32] SK1000 43
Comments to this Manuals